Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer

Saheera Azmi Hazarika; Tuhin Deshamukhya; Dipankar Bhanja; Sujit Nath

doi:10.1016/j.cjche.2017.03.034

Your Location：

Home >

Browse articles >

Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer

Fluid Dynamics and Transport Phenomena | Updated：2026-01-06

- Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer
- Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer
- 中国化学工程学报（英文版） 2017年25卷第9期页码：1121-1136
- Affiliations：
  
  Department of Mechanical Engineering, National Institute of Technology Silchar, Assam 0,India,788 01
- Author bio：
- Funds：
- DOI：10.1016/j.cjche.2017.03.034
  中图分类号：
- 纸质出版：2017
- Accepted：
Scan QR Code
Saheera Azmi Hazarika, Tuhin Deshamukhya, Dipankar Bhanja, 等. Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer[J]. 中国化学工程学报（英文版）, 2017,25(9):1121-1136.

Saheera Azmi Hazarika, Tuhin Deshamukhya, Dipankar Bhanja, Sujit Nath. Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer[J]. , 2017, 25(9): 1121-1136.
Saheera Azmi Hazarika, Tuhin Deshamukhya, Dipankar Bhanja, 等. Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer[J]. 中国化学工程学报（英文版）, 2017,25(9):1121-1136. DOI： 10.1016/j.cjche.2017.03.034.

Saheera Azmi Hazarika, Tuhin Deshamukhya, Dipankar Bhanja, Sujit Nath. Thermal analysis of a constructal T-shaped porous fin with simultaneous heat and mass transfer[J]. , 2017, 25(9): 1121-1136. DOI： 10.1016/j.cjche.2017.03.034.

摘要

Abstract

The present work establishes an analytical model for computing the temperature distribution

fin efficiency and optimum design parameters of a constructal T-shaped porous fin operating in fully wet condition. For more practical results

this study considers a cubic polynomial relationship between the humidity ratio of saturated air and the corresponding fin surface temperature. The temperature distribution has been determined by solving the highly non-linear governing equations using a semi-analytical transformation technique called Differential Transform Method. A comparison of the results with that of a numerical model shows that this transformation method is a very efficient and convenient tool for solution of non-linear problems. The effects of various geometric

thermo-physical and psychometric parameters on the temperature distribution

fin efficiency and optimum design condition have been investigated. Also

a comparison has been presented between solid and porous fins and the results point out that by selecting an appropriate value of porosity

the heat transfer rate can be increased than the corresponding solid fin.

关键词

Keywords

references

浏览量

410

Downloads

CSCD

文章被引用时，请邮件提醒。

Submit

工具集

关联资源

Mixing behavior and mass transfer of liquid—liquid two-phase flow in an annular microchannel with helical wires

Gold/Mg-Al mixed oxides catalysts for oxidative esterification of methacrolein: Effects of support size and composition on gold loading

Performance improvement of ultra-low Pt proton exchange membrane fuel cell by catalyst layer structure optimization

Bubble dispersion intensification via flow guidance and drainage in a bubble column with internals

Optimizing energy efficiency in fluid catalytic cracking units with GA and NSGA-II: A comprehensive simulation and multi-factor analysis