Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor

Mohamad-Taghi Rostami; Ali Daneshgar

doi:10.1016/j.cjche.2016.05.049

Your Location：

Home >

Browse articles >

Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor

Fluid Dynamics and Transport Phenomena | Updated：2026-01-06

- Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor
- Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor
- 中国化学工程学报（英文版） 2016年24卷第12期页码：1655-1663
- Affiliations：
  
  Department of Engineering, Mohaghegh Ardabili University, Daneshgah Street, Ardabil,Iran
- Author bio：
- Funds：
- DOI：10.1016/j.cjche.2016.05.049
  中图分类号：
- 纸质出版：2016
- Accepted：
Scan QR Code
Mohamad-Taghi Rostami, Ali Daneshgar. Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor[J]. 中国化学工程学报（英文版）, 2016,24(12):1655-1663.

Mohamad-Taghi Rostami, Ali Daneshgar. Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor[J]. , 2016, 24(12): 1655-1663.
Mohamad-Taghi Rostami, Ali Daneshgar. Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor[J]. 中国化学工程学报（英文版）, 2016,24(12):1655-1663. DOI： 10.1016/j.cjche.2016.05.049.

Mohamad-Taghi Rostami, Ali Daneshgar. Modeling and experimental studies of methyl methacrylate polymerization in a tubular reactor[J]. , 2016, 24(12): 1655-1663. DOI： 10.1016/j.cjche.2016.05.049.

摘要

Abstract

In this study

rheological examination of the mixture of a tubular reactor in which methyl methacrylate was polymerized has been studied. The

(flow behavior index) value of Power Law Model of mixture contained in the reactor has been determined within the span of 0.3492 to 0.9889 by curve fitting. Employing these numerical data for velocity profile

the reactor has been modeled. Moreover

the functions of the reactor have been compared in the three modes of plug

mixed and laminar flow. The results obtained in this research indicate that the polymethyl methacrylate mixture contained in the reactor is pseudo-plastic. Moreover

as the conversion grows

the velocity profile starts as a parabolic profile and approaches the plug mode; although it never reaches the plug. The other conclusions borne in this study indicate that when the reactor's radius is decreased

the conversion rate grows. However

as decreasing the radius would also reduce the productions rate

this procedure is not economical. Finally

in this modeling

the amount of conversion is equal to 56.47% at the end and according to its laboratory proportion which is 55.88%

it has reached the conclusion that the modeling d

uly undertaken is applicable and valid.

关键词

Keywords

references

浏览量

110

Downloads

CSCD

文章被引用时，请邮件提醒。

Submit

工具集

关联资源

Laminar flow of high-viscous non-Newtonian power-law and Bingham fluids in multiple structural bifurcation channel distributors: Flow patterns and pressure drop correlation

Multi-objective optimization of wastewater treatment using electrocoagulation

CFD simulation of hydrodynamics and mixing performance in dual shaft eccentric mixers

Microchannel reactors for Fischer-Tropsch synthesis: Experimental investigation and mathematical modeling

Comparative study of heat transfer and pressure drop for curved-twisted tubes utilized in chemical engineering