Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method

杨斌鑫; 欧阳洁; 刘春太; 李强

doi:10.1016/S1004-9541(10)60263-7

Your Location：

Home >

Browse articles >

Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method

Updated：2026-01-06

- Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method
- Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method
- 中国化学工程学报（英文版） 2010年18卷第4期页码：600-608
- Affiliations：
  
  1. School of Science, Northwestern Polytechnical University,Shaanxi,Xi'an,China,710129
  2. National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University,Zhengzhou,China,450002
- Author bio：
- Funds：
  
  Supported by the National Natural Science Foundation of China(10871159);the National Basic Research Program of China(2005CB321704)
- DOI：10.1016/S1004-9541(10)60263-7
  中图分类号：
- 纸质出版：2010
- Accepted：
Scan QR Code
杨斌鑫, 欧阳洁, 刘春太, 等. Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method[J]. 中国化学工程学报（英文版）, 2010,18(4):600-608.

YANG Binxin, OUYANG Jie, LIU Chuntai, LI Qiang. Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method[J]. , 2010, 18(4): 600-608.
杨斌鑫, 欧阳洁, 刘春太, 等. Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method[J]. 中国化学工程学报（英文版）, 2010,18(4):600-608. DOI： 10.1016/S1004-9541(10)60263-7.

YANG Binxin, OUYANG Jie, LIU Chuntai, LI Qiang. Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method[J]. , 2010, 18(4): 600-608. DOI： 10.1016/S1004-9541(10)60263-7.

摘要

Abstract

A non-isothermal injection molding process for a non-Newtonian viscous pseudoplastic fluid is simulated.A conservative interface capturing technique and the flow field solving method are coupled to perform a dynamic simulation.The validity of the numerical method is verified by a benchmark problem.The melt interface evolution versus time is captured and the physical quantities such as temperature

velocity and pressure at each time step are obtained with corresponding analysis.A"frozen skin"layer with the thickness increasing versus time during the injection process is found.The fact that the"frozen skin"layer can be reduced by increasing the injection velocity is numerically verified.The fountain flow phenomenon near the melt interface is also captured.Moreover

comparisons with the non-isothermal Newtonian case show that the curvatures of the interface arcs and the pressure contours near the horizontal mid-line of the cavity for the non-Newtonian pseudoplastic case is larger than that for the Newtonian case.The velocity profiles are different at different positions for the non-Newtonian pseudoplastic case

while in the case of Newtonian flow the velocity profiles are parabolic and almost the same at different positions.

关键词

Keywords

references

浏览量

Downloads

CSCD

文章被引用时，请邮件提醒。

Submit

工具集

关联资源

New approach to develop a 3D non-isothermal computational framework for injection molding process based on level set method

Multilevel synergistic enhanced trapezoidal open microchannel heat sink for thermal management of electronic devices

Multiscale synergistic enhancement mechanism of solid—liquid mixing in multi-shaft stirred reactors under variable-speed operation

Machine learning-assisted characterization of oil micro-displacement hydrodynamics by bionanofluid-flooding in microchannel sand-packed porous media towards enhanced oil recovery

Evaluation of live Cryo-ECT system for liquid nitrogen-vapor nitrogen flow