Rapid and Continuous Production of LiFePO<sub>4</sub>/C Nanoparticles in Super Heated Water

于文利; 赵亚平; 饶群力

doi:10.1016/S1004-9541(09)60051-3

Your Location：

Home >

Browse articles >

Rapid and Continuous Production of LiFePO₄/C Nanoparticles in Super Heated Water

Updated：2026-01-06

- Rapid and Continuous Production of LiFePO₄/C Nanoparticles in Super Heated Water
- Rapid and Continuous Production of LiFePO₄/C Nanoparticles in Super Heated Water
- 中国化学工程学报（英文版） 2009年17卷第1期页码：171-174
- Affiliations：
  
  1. School of Chemistry and Chemical Technology, Shanghai Jiao Tong University,Shanghai,China,200240
  2. Instrumental Analysis Centre, Shanghai Jiao Tong University,Shanghai,China,200240
- Author bio：
- Funds：
- DOI：10.1016/S1004-9541(09)60051-3
  中图分类号：
- 纸质出版：2009
- Accepted：
Scan QR Code
于文利, 赵亚平, 饶群力. Rapid and Continuous Production of LiFePO₄/C Nanoparticles in Super Heated Water[J]. 中国化学工程学报（英文版）, 2009,17(1):171-174. DOI: 10.1016/S1004-9541(09)60051-3.

/C Nanoparticles in Super Heated Water[J]. , 2009, 17(1): 171-174.
于文利, 赵亚平, 饶群力. Rapid and Continuous Production of LiFePO₄/C Nanoparticles in Super Heated Water[J]. 中国化学工程学报（英文版）, 2009,17(1):171-174. DOI: 10.1016/S1004-9541(09)60051-3. DOI：

/C Nanoparticles in Super Heated Water[J]. , 2009, 17(1): 171-174. DOI： 10.1016/S1004-9541(09)60051-3.

摘要

A rapid and continuous method for production of LiFePO

/C nanoparticles in super heated water is described

wherein soluble starch was used as carbon precursor.The effects of pH

flow rate

temperature

and pressure on the formation of LiFePO

/C particles were investigated.Results showed that the pH value was the key factor on the formation of phase pure LiFePO

which only formed at pH=7;the LiFePO

/C occurred as particles with about 70-200 nm size and LiFePO

was covered by a thin carbon layer;higher flow rate

higher pressure

and lower temperature led to smaller particles of LiFePO

/C.

Abstract

A rapid and continuous method for production of LiFePO

/C nanoparticles in super heated water is described

wherein soluble starch was used as carbon precursor.The effects of pH

flow rate

temperature

and pressure on the formation of LiFePO

/C particles were investigated.Results showed that the pH value was the key factor on the formation of phase pure LiFePO

which only formed at pH=7;the LiFePO

/C occurred as particles with about 70-200 nm size and LiFePO

was covered by a thin carbon layer;higher flow rate

higher pressure

and lower temperature led to smaller particles of LiFePO

/C.

关键词

Keywords

references

浏览量

183

Downloads

CSCD

文章被引用时，请邮件提醒。

Submit

工具集

关联资源

Low-temperature conversion of methane to oxygenates by supported metal catalysts: From nanoparticles to single atoms

Fabrication of a highly efficient new nanocomposite polymer gel for controlling the excess water production in petroleum reservoirs and increasing the performance of enhanced oil recovery processes

Experimental study on thermo-hydraulic performances of nanofluids flowing through a corrugated tube filled with copper foam in heat exchange systems

Review on application of nanoparticles for EOR purposes: A critical review of the opportunities and challenges

Influence of nanoparticle concentrations on flow boiling heat transfer coefficients of Al2O3/R141b in micro heat exchanger by direct metal laser sintering

Rapid and Continuous Production of LiFePO4/C Nanoparticles in Super Heated Water

Rapid and Continuous Production of LiFePO4/C Nanoparticles in Super Heated Water

DOI：10.1016/S1004-9541(09)60051-3

摘要

Abstract

关键词

Keywords

references

Rapid and Continuous Production of LiFePO₄/C Nanoparticles in Super Heated Water

Rapid and Continuous Production of LiFePO₄/C Nanoparticles in Super Heated Water