Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers
Fluid Dynamics and Transport Phenomena|Updated:2026-01-06
|
Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers
Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers
中国化学工程学报(英文版)2019年27卷第10期 页码:2284-2292
Affiliations:
1. School of Architecture, Harbin Institute of Technology,Harbin,China,150090
2. Key Laboratory of Cold Region Urban and Rural Human Settlement Environment Science and Technology, Ministry of Industry and Information Technology,Harbin,China,150090
3. School of Energy Science and Engineering, Harbin Institute of Technology,Harbin,China,150001
4. School of Energy and Power Engineering, Northeast Electric Power University,Jilin,China,132012
Author bio:
Funds:
DOI:
中图分类号:
纸质出版:2019
Accepted:
Scan QR Code
Wenke Zheng, Weihua Cai, Yiqiang Jiang. Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers[J]. 中国化学工程学报(英文版), 2019,27(10):2284-2292.
Wenke Zheng, Weihua Cai, Yiqiang Jiang. Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers[J]. Chinese Journal of Chemical Engineering, 2019, 27(10): 2284-2292.
Wenke Zheng, Weihua Cai, Yiqiang Jiang. Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers[J]. 中国化学工程学报(英文版), 2019,27(10):2284-2292.DOI:
Wenke Zheng, Weihua Cai, Yiqiang Jiang. Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers[J]. Chinese Journal of Chemical Engineering, 2019, 27(10): 2284-2292.DOI:
Distribution performance of gas-liquid mixture in the shell side of spiral-wound heat exchangers
The non-uniformity of gas-liquid mixture is a critical issue which leads to the heat transfer deterioration of spiralwound heat exchangers (SWHEs). Two-phase mass flow rate and the content of gas are important parameters as well as structural parameters which have prominent influences on flow distribution uniformity of SWHE shell side. In order to investigate the influences of these parameters
an experimental test system was built using water and air as mediums and a novel distributor named "tubes distributor" was designed. The effects of mass flow rate and the content of gas on two-phase distribution performance were analyzed
where the mass flow rate ranged from 28.4 to 171.9 kg·h
-1
and the content of gas changed from 0.2 to 0.8
respectively. The results showed that the mixture mass flow rate considerably influenced the liquid distribution than that of gas phase and the larger mass flow rate exhibited the better distribution uniformity of two-phase flow. It was also found that the tubes distributor had the better two-phase uniformity when the content of gas was around 0.4. Tube diameter played an important role in the distribution of gas phase and slit width was more si
gnificant for the uniformity of liquid phase.
关键词
Keywords
references
The trial reading is over, you can activate your VIP account to continue reading.
Experimental analysis of internal flow and spray characteristics of flow focusing/blurring nozzle
Hydrodynamic analysis of carbon nanotube clusters in distributor-less conical fluidized beds with step-by-step scaling
Gas-liquid-liquid slug flow and mass transfer in hydrophilic and hydrophobic microreactors
Rapid velocity reduction and drift potential assessment of off-nozzle pesticide droplets
Multi-fluid Eulerian simulation of binary particles mixing and gas-solids contacting in high solids-flux downer reactor equipped with a lateral particle feeding nozzle
相关作者
Xu He
Ming Lv
Zhi Ning
Jin Zhao
Yan He
Lianlian Wang
Dianming Chu
Qianpeng Dong
相关机构
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University
School of Mechanical Engineering, Beijing Institute of Technology
Shandong Dazhan Nano Materials Co., Ltd.
Shandong Engineering Laboratory for Preparation and Application of High-performance Carbon-Materials, College of Electromechanical Engineering, Qingdao University of Science and Technology