Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province

Zhang Yuhao; Zhao Peiqiang; Li Mingli; Zhang Xinglin; Liu Zewei; Yan Dahai; Chen Chao; Fang Wei

doi:10.1016/j.cjche.2025.08.006

Your Location：

Home >

Browse articles >

Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province

Updated：2026-03-13

- Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province
- Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province
- 中国化学工程学报（英文） 2026年89卷第1期页码：220-229
- Affiliations：
  
  Lanzhou University, Lanzhou 730000, China
  Zhengdong Space Industry Co., Ltd., Beijing 100020, China
  Gansu Academy of Eco-environmental Sciences, Lanzhou 730030, China
  Faculty of Environmental Science and Engineering, Kunming University of Science and Technology, Kunming 650500, China
  Research Institute of Solid Waste Management, Chinese Research Academy of Environmental Sciences, Beijing 100012, China
- Author bio：
  
  Corresponding authors. E-mail addresses: chen.chao@craes.org.cn(C. Chen)
  fangwei@stu.kust.edu.cn(W. Fang).
- Funds：
  
  This research was supported by the Key Research and Devel-opment Program of Gansu Province(22YF7FA070);the National Natural Science Foundation of China(22406076;22466026);the Basic Research Project of Yunnan Province.(202301BE070001-017;202401CF070139;202401AS070085)
- DOI：10.1016/j.cjche.2025.08.006
  中图分类号：
- 收稿：2025-05-09，
  
  修回：2025-08-08，
  
  录用：2025-08-12，
  
  网络首发：2025-09-04，
  
  纸质出版：2026-01
- Accepted：
Scan QR Code
Zhang Yuhao, Zhao Peiqiang, Li Mingli, 等. Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province[J]. 中国化学工程学报（英文）, 2026,89(1):220-229.

Zhang Yuhao, Zhao Peiqiang, Li Mingli, et al. Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province[J]. Chinese Journal of Chemical Engineering, 2026, 89(1): 220-229.
Zhang Yuhao, Zhao Peiqiang, Li Mingli, 等. Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province[J]. 中国化学工程学报（英文）, 2026,89(1):220-229. DOI： 10.1016/j.cjche.2025.08.006.

Zhang Yuhao, Zhao Peiqiang, Li Mingli, et al. Study on pollutant reduction effect and environmental benefits of ultra-low emission retrofit of iron and steel sintering process: A case study of a steel group in Gansu province[J]. Chinese Journal of Chemical Engineering, 2026, 89(1): 220-229. DOI： 10.1016/j.cjche.2025.08.006.

摘要

Abstract

Iron and steel industry is one of the main sources of air pollution emissions in China. The sintering process is an important link in the blast furnace ironmaking process

but it is also accompanied by a large number of pollutants. Under the background of ultra-low emissions

iron and steel enterprises urgently need to upgrade their existing processes to address the existing process in practical application problems. In this study

a steel group in Gansu Province was taken as an example. By comparing and analyzing the pollutant emission characteristics before and after the ultra-low emission retrofit

the collaborative control effect of the combined process on SO

particulate matter

and dioxins after the new retrofit was systematically evaluated. The results show that after the retrofit

the concentrations of particulate matter

and NO

have dropped to near-zero levels

and the dioxin removal efficiency has reached 98.87%

with all indicators being better than the national ultra-l

ow emission standards. The study confirms that the optimal combination of multi-pollutant collaborative treatment technologies is the key to achieving efficient emission reduction

among which selective catalytic reduction technology has a particularly significant synergistic removal effect on NO

and dioxins. This study provides an important technical reference and practical basis for the ultra-low emission retrofit of the steel industry

and has important guiding significance for promoting the green retrofit of the industry. Its ultra-low emission retrofit is of great significance for achieving green and low-carbon development.

关键词

Keywords

references

Y.X. Liu, H.J. Li, J.H . Guan, S.D. Feng, S. Guo, The impact of Chinese steel product prices based on the midstream industry chain, Resour. Policy 63 (2019) 101415.

L. Tang, X.D. Xue, M. Jia, H. Jing, T. Wang, R.Q. Zhen, M.T. Huang, J. Tian, J. Guo, L. Li, X. Bo, S.Y. Wang, Iron and steel industry emissions and contribution to the air quality in China, Atmos. Environ. 237 (2020)117668.

J. Kim, B.K. Sovacool, M. Bazilian, S. Griffiths, J. Lee, M. Yang, J. Lee, Decarbonizing the iron and steel industry: a systematic review of sociotechnical systems, technological innovations, and policy options, Energy Res. Social Sci. 89 (2022) 102565.

K.L. Zhou, S.L. Yang, Emission reduction of china ׳ s steel industry: progress and challenges, Renew. Sustain. Energy Rev. 61 (2016)319—327.

L. Klime ˇ s, M. B ˇ rezina, T. Mauder, P. Charva't, J.J. Kleme ˇ s, J. Sˇteˇtina, Dry cooling as a way toward minimisation of water consumption in the steel industry: a case study for continuous steel casting, J. Clean. Prod. 275(2020)123109.

E. Mousa, C. Wang, J. Riesbeck, M. Larsson, Biomass applications in iron and steel industry: an overview of challenges and opportunities, Renew. Sustain. Energy Rev. 65 (2016)1247—1266.

S. Zhang, D.W. Jiang, Z.Y. Wang, Y.B. Zong, J.L. Zhang, F.W. Wang, R.S. Si, S.S. Zhang, X.F. Zhou, J. Pang, Sulfur migration behavior in sintering and pelletizing processes: a review, Steel Res. Int. 94 (11) (2023) 2200904.

Y.L. Zheng, P. Cheng, Z.K. Li, C.H. Fan, J.C. Wen, Y. Yu, L. Jia, Efficient removal of gaseous elemental mercury by Fe-UiO-66@BC composite adsorbent: performance evaluation and mechanistic elucidation, Sep. Purif. Technol. 372 (2025) 133463.

M.B. Dai, B.S. Gu, P.C. Su, Y.C. Zhou, Q.M. Meng, D.S. Li, M.F. Zhu, T.J. Chun, Examining low nitrogen oxides combustion in iron ore sintering: utilization of reductants, Renew. Sustain. Energy Rev. 205(2024)114864.

Z.L. Cheng, J. Yang, L. Zhou, Y. Liu, Q.W. Wang, Characteristics of charcoal combustion and its effects on iron-ore sintering performance, Appl. Energy 161(2016)364—374.

X.H. Zhang, P. Feng, J.R. Xu, L.B. Feng, S. Qing, Numerical research on combining flue gas recirculation sintering and fuel layered distribution sintering in the iron ore sintering process, Energy 192 (2020) 116660.

L.X. Qian, T.J. Chun, H.M. Long, J.X. Li, Z.X. Di, Q.M. Meng, P. Wang, Emission reduction research and development of PCDD/Fs in the iron ore sintering, Process Saf. Environ. Prot. 117 (2018)82—91.

L. Cui, K.M. Ba, F.Q. Li, Q.S. Wang, Q. Ma, X.L. Yuan, R.M. Mu, J.L. Hong, J. Zuo, Life cycle assessment of ultra-low treatment for steel industry sintering flue gas emissions, Sci. Total Environ. 725(2020)138292.

X. Sun, J. Li, F. Zhu, The current situation and challenges of air pollution prevention and control in China's thermal power industry, Electr. Power 51 (6)(2018)2—10. (in Chinese)

J. Liu, S. Wang, H.H. Yi, X.L. Tang, Z.L. Li, Q.J. Yu, S.Z. Zhao, F.Y. Gao, Y.S. Zhou, Y.X. Wang, Air pollutant emission and reduction potentials from the sintering process of the iron and steel industry in China in 2017, Environ. Pollut. 307 (2022) 119512.

W.M. Song, J.N. Zhou, B. Wang, S. Li, J. Han, New insight into investigation of reduction of desulfurization ash by pyrite for clean generation SO 2 , J. Clean. Prod. 253 (2020) 120026.

T.J. Wei, J. Zhang, K.S. An, N. Shi, P.F. Li, B. Li, Recent advances in recycle of industrial solid waste for the removal of SO 2 and NO x based on solid waste sorts, removal technologies and mechanism, Sep. Purif. Technol. 364 (2025) 132338.

F.W. Lin, Z.H. Wang, Z.M. Zhang, Y. He, Y.Q. Zhu, J.M. Shao, D.K. Yuan, G.Y. Chen, K.F. Cen, Flue gas treatment with ozone oxidation: an overview on NO x , organic pollutants, and mercury, Chem. Eng. J. 382 (2020) 123030.

F. Mene'ndez, A. Go'mez, F. Voces, V. García, Porcelain insulators in electrostatic precipitator, J. Electrost. 76 (2015) 188—193.

L. Chen, Y.F. Liao, S.R. Xin, X.X. Song, G.C. Liu, X.Q. Ma, Simultaneous removal of NO and volatile organic compounds (VOCs) by Ce/Mo doping-modified selective catalytic reduction (SCR) catalysts in denitrification zone of coalfired flue gas, Fuel 262 (2020) 116485.

W. Shi, M. Yang, X. Zhang, S. Li, Q. Yao, Ultra-low emission technology routes and synergistic removal for coal-f ired power plants, Proc. CSEE 36(16)(2016) 4308—4318. (in Chinese)

L. Tomas da Rocha, H. Kim, C.M. Lee, S.M. Jung, Mechanism of NO x formation from nitrogen in the combustion of the coals used in sintering process, Metall. Mater. Trans. B 51(5)(2020)2068—2078.

H. Zhou, P.N. Ma, M.X. Zhou, Z.Y. Lai, M. Cheng, Experimental investigation on the conversion of fuel-N to NO x of quasi-particle in flue gas recirculation sintering process, J. Energy Inst. 92 (5) (2019) 1476—1486.

L. Yao, Q.C. Liu, S. Mossin, D. Nielsen, M. Kong, L.J. Jiang, J. Yang, S. Ren, J. Wen, Promotional effects of nitrogen doping on catalytic performance over manganese-containing semi-coke catalysts for the NH 3 -SCR at low temperatures, J. Hazard. Mater. 387 (2020) 121704.

Y. Kang, C. Liu, Y.-Z. Zhang, H.-W. Xing, K. Zhao, Flue gas circulating sintering based on biomass fuel on reduction of NO x and SO 2 emission, ISIJ Int. 60 (8) (2020) 1633—1640.

C. Ren, T. Zhu, T. Zhu, D. Lyu, The formation rules of NO x and SO 2 during sintering and the influence of sintering material composition on NO x emissions, Environ. Sci. 35 (10) (2014) 3669—3673. (in Chinese)

Z. Hao, S. Wu, X. Duan, H. Han, Practices for reducing energy consumption in the sintering process at Baotou Steel, Sinter. Pelletiz. 35(4)(2010)46—49. (in Chinese)

J.Y. Yu, R.S. Xu, J.L. Zhang, A.Y. Zheng, A review on reduction technology of air pollutant in current China's iron and steel industry, J. Clean. Prod. 414(2023) 137659.

W.Q. Sun, Y. Zhou, J.X. Lv, J.Z. Wu, Assessment of multi-air emissions: case of particulate matter (dust), SO 2 , NO x and CO 2 from iron and steel industry of China, J. Clean. Prod. 232 (2019) 350—358.

J.P. Birat, Society, materials, and the environment: the case of steel, Metals 10 (3)(2020)331.

Y.F. Wang, L.X. Qian, Z.W. Yu, T.J. Chun, H.M. Long, X.J. Wu, J.X. Li, Inhibition behavior of PCDD/Fs congeners by addition of N-containing compound in the iron ore sintering, Aerosol Air Qual. Res. 20 (11) (2020) 2568—2579.

C.H. Cui, M.J. Liu, L. Li, D.H. Yan, C. Chen, M.W. Wang, J.Y. Wang, Q.F. Huang, Effects of increasing chlorine concentration in feedstock on the emission and distribution characteristic of dioxins in circular fluidized bed boiler, Environ. Sci. Pollut. Res. Int. 30(4)(2023)10202—10212.

D.R. Anderson, R. Fisher, Sources of dioxins in the United Kingdom: the steel industry and other sources, Chemosphere 46(3) (2002)371—381.

L.N. Liu, W.P. Li, Z.S. Xiong, D. Xia, C.W. Yang, W. Wang, Y.F. Sun, Synergistic effect of iron and copper oxides on the formation of persistent chlorinated aromatics in iron ore sintering based on in situ XPS analysis, J. Hazard. Mater. 366(2019)202—209.

T. Zhu, Q. Liu, Y. Li, X. Yan, F. Qi, M. Ye, Emission characteristics and control technologies of multi-pollutants in iron and steel sintering flue gas, Sci. Technol. Rev. 32(33)(2014)51—56. (in Chinese)

L. Chen, X.N. Feng, Z.Q. Ai, J.L. Xie, X.L. Liang, S. Xia, C. Xie, Research progress on comprehensive utilization of dust in sintering machine head, J. Salt Sci. Chem. Ind. 52(8)(2023) 46—50.

W. Tang, D. Zhang, G. Wu, G. Sun, Resource utilization technology of electrostatic precipitator dust from sintering machine head, Mod. Min. 33 (9) (2017) 188—191. (in Chinese)

Y. Xiong, Practice of ultra-low emission engineering renovation for power plants burning high-sulfur coal, Resour. Conserv. Environ. Protec. (9) (2024) 25—28. (in Chinese)

浏览量

Downloads

CSCD

文章被引用时，请邮件提醒。

Submit

工具集

关联资源

Fabrication of superhydrophilic surface on copper substrate by electrochemical deposition and sintering process

Study on the deactivation mechanism of mercury chloride catalyst employed for polyvinyl chloride production

Microfluidic extraction of phenolic compounds from wastewater in the straight/helical/in-plane spiral microchannels

Enhancing corrosion resistance of heat-assisted forming titanium bipolar plate for proton exchange membrane fuel cell through optimized heat treatment

Optimized anchor and cell wall engineering boost UDP-glycosyltransferase display for glycyrrhetinic acid glycosylation in Komagataella phaffii