Droplet characteristics in the multi-staged high speed disperser with single inlet

Ao Nie; Ziqi Cai; Zhengming Gao; Zhimiao Wang; Archie Eaglesham

doi:10.1016/j.cjche.2018.12.017

Your Location：

Home >

Browse articles >

Droplet characteristics in the multi-staged high speed disperser with single inlet

Fluid Dynamics and Transport Phenomena | Updated：2026-01-06

- Droplet characteristics in the multi-staged high speed disperser with single inlet
- Chinese Journal of Chemical Engineering Vol. 27, Issue 8, Pages: 1756-1764(2019)
- Affiliations：
  
  1. State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology,Beijing,China,100029
  2. Huntsman Polyurethanes, 8 Everberg,Belgium,B307
- Author bio：
- Funds：
- DOI：10.1016/j.cjche.2018.12.017
  CLC：
- Published：2019
- Accepted：
Scan QR Code
Ao Nie, Ziqi Cai, Zhengming Gao, Zhimiao Wang, Archie Eaglesham. Droplet characteristics in the multi-staged high speed disperser with single inlet[J]. Chinese Journal of Chemical Engineering, 2019, 27(8): 1756-1764.
DOI：

Ao Nie, Ziqi Cai, Zhengming Gao, Zhimiao Wang, Archie Eaglesham. Droplet characteristics in the multi-staged high speed disperser with single inlet[J]. Chinese Journal of Chemical Engineering, 2019, 27(8): 1756-1764. DOI： 10.1016/j.cjche.2018.12.017.

摘要

Abstract

Droplet characteristics in the cavity zone of a multi-staged high speed disperser with single inlet were studied in this paper. The influences of both the operating and structural parameters on the mean droplet diameter

size distribution and liquid flux distribution were quantitatively analyzed. The result showed that the mean droplet diameter decreased with the increase of rotational speed and the number of rotors; whilst there is little influence on the inlet flow rate. In the experimental range

the minimum value of mean droplet diameter is 0.57 mm

0.48 mm

0.41 mm in the two-staged

three-staged and four-staged rotors

respectively. The Rosin-Rammler (

R-R

) distribution could describe the droplet size distribution appropriately

and it became uniform with the increase of rotational speed and the number of rotor

while the inlet flow rate had little effect on the droplet size distribution. The liquid flux distribution curves were always unimodal. With the increase of rotational speed

the location of maximum liquid flux ratio moved from zone 3 to zone 4 and this value decreased from 22.1% to 18.1%. Using Coefficient of Variation (CV) to indicate the uniformity of liquid flux distribution

it was found that the CV decreases from 47.5% to 22.7% when the number of rotor increased from 2 to 4.

关键词

Keywords

references

Views

Downloads

CSCD

Alert me when the article has been cited

Submit

Tools

Publicity Resources

The flow behavior of droplet adsorption on a liquid–liquid interface accompanied by cross-linking reaction and phase separation in a microchannel

Coalescence dynamics of two droplets of different viscosities in T-junction microchannel with a funnel-typed expansion chamber

Effects of different nozzle materials on atomization results via CFD simulation

Microscopic and macroscopic atomization characteristics of a pressure-swirl atomizer, injecting a viscous fuel oil

Experimental study of a heavy fuel oil atomization by pressure-swirl injector in the application of entrained flow gasifier

Related Author

Youguang Ma

Chunying Zhu

Taotao Fu

Haozhe Yi

Youguang Ma

Weixi Guo

Licheng Wang

Xiangyu Li

Related Institution

State Key Laboratory of Chemical Engineering, School of Chemical Engineering and Technology, Tianjin University

Dalian FISTA Specialized Chemistry Co. Ltd., 131 Guangxian Road

Research Institute of Dalian University of Technology in Shenzhen, Gaoxin South fourth Road, Nanshan District

State Key Laboratory of Fine Chemicals, Dalian University of Technology, 2 Linggong Road

School of Mechanical Engineering, Iran University of Science and Technology(IUST), P. O. B. 16765-163, Tehran

⁰